Calamine Network Configuration
Overall Network Configuration
Figure 5: Overall network port configuration procedure.
Calamine boasts three network ports. The Management port is used to configure the device and the two SFP+ ports are used to send data. The default Calamine network values are listed in Table 1. An example of a known functioning client networking configuration is shown in Table 2. Figure 6 has the same information displayed differently.
The Management port is used to configure the device, while the two SFP+ ports are used to send data. Each SFP+ data port is connected to a specific antenna port. To properly configure Calamine, each port must be properly configured.
Note
The Calamine Management port requires connection to an interface that supports half-duplex mode.
Default Calamine Network Configuration
Table 1: Default Calamine Interface Addresses, Including UDP Destination Ports for SFP+ Headers.
| SFP+ A | SFP+ B | MGMT | |
|---|---|---|---|
| Calamine IP Address | 10.10.10.2 | 10.10.11.2 | 192.168.10.2 |
| Default MGMT Port | - | - | 42799 |
| Radio Channels | A, C | B, D | - |
| Destination IP (Rx) | 10.10.10.10 | 10.10.11.10 | - |
| Rx UDP Ports | 42820, 42821 | 42822, 42823 | - |
| Flow Control Ports | 42809 | 42810 | - |
| Source IP (Tx) | any | any | - |
| Tx UDP Ports | 42824, 42825 | 42826, 42827 | - |
Table 2: Example Host Computer Network Configuration for Calamine Default Settings
| SFP+ A | SFP+ B | MGMT | |
|---|---|---|---|
| Host IP Address | 10.10.10.10/24 | 10.10.11.10/24 | 192.168.10.3/24 |
| Net Mask | 255.255.255.0 | 255.255.255.0 | 255.255.255.0 |
| Broadcast | 10.10.10.255 | 10.10.11.255 | 192.168.10.255 |
| MTU | 9000 | 9000 | 1500 |
Figure 6: Default networking set up for Calamine.
The destination IP addresses for receive ports may be modified using the web GUI. The default configuration sees information from Rx A sent to the destination IP address of 10.10.10.10.
Configure Networking
To configure your network to work with Calamine, see how to configure networking.
Verifying the Setup
To test your setup and operation, read how to verify operation.
Configuring a Custom Calamine Management IP Address
To configure a custom Calamine MGMT IP address, see how to configure a custom management IP address.
Footnotes
-
\(^1\) This is how Calamine ships. If you have any issues or concerns regarding your Micro SD card, please contact us.
-
\(^2\) It is very important to ensure that network devices or interfaces intended to be used to connect to Calamine support 10GBASE-R. The 10GBASE-R family includes:
- 10GBASE-KR,
- 10GBASE-SR,
- 10GBASE-LR,
- and 10GBASE-ER interfaces.
There is a significant difference between a 10GBASE-X interface (4 serial lanes specified to 3.125Gbps using 8b/10b coding), and the 10GBASE-R interface (1 serial lane specified to 10.3125Gbps using 64b/66b coding) that Calamine uses.
Although both standards may expose the same mechanical SFP+ interface (and thereby allowing you to mechanically connect the two interfaces) the standards are fundamentally incompatible. Connecting Calamine (10GBASE-R) to a network card that only supports 10GBASE-X or 10GBASE-T will not work.